How to Fix “Media Is Write Protected” in Windows

By 2 months ago

Compose assurance is a component that means to keep clients from unintentionally erasing or changing the information on a circle or other stockpiling gadgets. Sadly, now and then Windows will not work with a drive since it distinguishes it as compose secured when it shouldn’t be.

Fortunately, there are different fixes for the “Media Is Write Protected” mistake in Windows. How about we see, beginning with the clearest fixes.

Check Your Media for a Write Protection Switch

In case you’re experiencing difficulty designing or keeping in touch with a USB streak drive, SD card or comparative outer stockpiling gadget, check for a compose assurance switch. This is an actual sliding switch that can be flipped here and there, as displayed in the image above.

In case it was inadvertently driven into the compose assurance position, you will not have the option to organize or keep in touch with the drive till you switch it back. Make certain to launch the drive first prior to flipping the switch!

Removing Write Protection from Files and Folders

If your problem is write protection of specific files and not the entire disk, it’s easy to fix:

  1. Open File Explorer.
  1. Navigate to the files and/or folders that are write protected.
  2. Select the files and/or folders.
  3. Right-click on your selection and select Properties.
  4. Under the General tab, make sure the box labeled Read-Only is unchecked.
  5. Select Apply and then OK.

Run a Disk Scan

One great bit of housekeeping to do before you begin playing with the guts of your working framework is to do an actual output of the drive being referred to. On the off chance that the plate is harmed or undermined, that might cause a compose assurance mistake.

To run a full disk scan in Windows:

  1. Open File Explorer.
  2. Right-click on the drive you want to scan and select Properties.
  3. Go to the Tools tab.
  4. Select Check.
  5. Select Scan and Repair Drive.

Run a Full Malware Scan

Certain malware may compose secure drives to forestall their own erasure. It’s not the most probable explanation you’re getting the compose insurance mistake, yet since a malware examination is speedy and simple to do, it merits performing one at any rate.

In the event that eliminating the malware from the framework or circle doesn’t fix the issue follow the means referenced beneath to return the drive to ordinary.

Check System Files for Corruption

The final piece of essential prep work when trying to make a drive writable again is to run the System File Checker (SFC). This will compare all of your crucial system files to the gold standard originals. If any files have been altered or corrupted, pristine new versions will be downloaded and installed.

Use Advanced Formatting Tools

Assuming all you need to do is design a drive, yet you’re being impeded by composing assurance, then, at that point, the appropriate response might be to utilize an arranging utility with somewhat more muscle. Numerous clients declare by the HP USB Formatting Tool to menace compose secured outer plates into collaborating.

It’s additionally one of a handful of the utilities that allows you to design huge plates into FAT32 design, something vital occasionally. Remember that you need to run this application with chairman advantages for it to work. Results are purportedly blended, yet the accompanying arrangements are somewhat more perplexing, so assuming you need to take a risk with an organizing utility application first this is one choice.

Remove Write Protection With DiskPart

DiskPart is a powerful command-line utility in Windows that can remove attributes from entire disks or specific partitions.

  1. First, insert the USB drive that is write protected, if applicable.
  2. Open the Start Menu and type diskpart.
  3. Select the diskpart run command from the results.
  4. If you’re asked for administrator permissions, say yes.
  5. At the command line for DiskPart, type list disk and press Enter.
  6. Look for your USB disk in the list of drives, make a note of its disk number. You’ll need it shortly!
  7. Now, type select disk #, but replace the # with the correct disk number. Then press Enter.
  8. Type attributes disk clear readonly and then press the Enter key.
  9. After receiving the confirmation message, type Exit and press Enter.

Remove Write Protection with Regedit

Some of the time a drive is set apart as compose ensured and you’ll get the “Media is Write Protected” mistake on the grounds that the relating esteem in the Windows vault is inaccurate. In the event that conceivable, try not to play in your vault. In case this is your final hotel, if it’s not too much trouble, consider backing up your library in the event that something turns out badly.

With that being said, here’s how to remove write protection from a USB drive in Windows:

  1. Insert the drive you want to modify into a USB port.
  2. Open the Start Menu and type Registry Editor.
  3. Select Registry Editor from the results.
  1. In the registry editor, navigate to HKEY_LOCAL_MACHINE > SYSTEM > CurrentControlSet > Control > StorageDevicePolicies.
  2. Double-click WriteProtect. This will open the Edit DWORD window.
  3. Look for the Value data box, then enter 0 as the new value.
  1. Select OK and close the registry editor.
  2. Restart your computer and check the disk again.

What if there is no StorageDevicePolicies value to change?

Creating StorageDevicePolicies

In case you’re unfortunate enough not to have the right vault worth to transform, you’re simply must make it yourself. Relax, you have this.

  1. Open the Registry Editor as detailed above.
  2. Navigate to HKEY_LOCAL_MACHINE > SYSTEM > CurrentControlSet > Control.
  1. Right-click in an empty area of the right-hand pane and select New > Key.
  2. Name the new key StorageDevicePolicies and press Enter to confirm.
  3. Select StorageDevicePolicies.
  4. Again, right-click in the empty space of the right hand pane and select New > DWORD(32-bit) Value.
  5. Name the new DWORD value WriteProtect and press Enter to confirm.
  6. Double-click WriteProtect. This will open the Edit DWORD window.
  7. Look for the Value data box, then enter 0 as the new value.
  8. Select OK and close the registry editor.
  9. Restart your computer and check the disk again.
Share
asktechnicians

Recent Posts